إعـــــــلان

Collapse

.

,
See more
See less

صوت طقطة خفيفة فى متور النيو اكسنت لما ابطل العربية

Collapse
X
 
  • Filter
  • الوقت
  • Show
Clear All
new posts

  • #16
    شكراً أ/ مروان على الرد
    العربية فيرنا 2009 عاملة 9500 كم , لسه هاحجز صيانة العشرتلاف
    أخر صيانه كانت الخمسه
    لسه البوجيهات عليها كتير .. هوه ممكن يكون عيب منها ؟؟!!!
    [SIGPIC][/SIGPIC]
    https://www.facebook.com/groups/SWIFTCLUBINEGYPT/

    Comment


    • #17
      يابرنس
      الفيرنا معروفه بالحكايه دى لما بتتركن فتره

      اول ماتيجى تدور بعد كده بتقعد ترعش لمده 5 او 10 ثوانى بالكتير لو هيه كده يبقى اضمن كل الفيرنات كده
      [CENTER][SIZE=5][COLOR=gray][COLOR=#000000][SIZE=5][FONT=Times New Roman][B][SIZE=6][COLOR=blue]سبحان الله و بحمده سبحان الله العظيم[/COLOR][/SIZE][/B][/FONT][/SIZE][/COLOR][/COLOR][/SIZE][SIZE=5][COLOR=gray][COLOR=#000000][SIZE=5][/CENTER]
      [CENTER][CENTER][FONT=Times New Roman][B][SIZE=6][COLOR=blue][/COLOR][/SIZE][/B][/FONT][/CENTER]
      [/SIZE][/COLOR][/COLOR][/SIZE][/CENTER]

      Comment


      • #18
        المشاركة الأصلية كتبت بواسطة El Prince مشاهدة المشاركة
        شكراً أ/ مروان على الرد
        العربية فيرنا 2009 عاملة 9500 كم , لسه هاحجز صيانة العشرتلاف
        أخر صيانه كانت الخمسه
        لسه البوجيهات عليها كتير .. هوه ممكن يكون عيب منها ؟؟!!!
        احتمال كبير لأن البوجيهات اللي بتنزل فيها Champion على حد علمي وان كفائتها بتقل بشكل ملحوظ بعد 10,000 كيلومتر من الاستخدام
        وفي احتمال تاني انه يكون السوفت وير بتاع كنترول عربيتك محتاج Updating
        علشان العربية بتعمل
        Rough Idling at cold start conditions

        ومش بالضرورة ان علشان في عربية تانية زي عربيتك بتعمل كده يبقى ده عادي
        وليه مايكونش الكنترول فيه كود محتاج Updating والتوكيل مكبر دماغه
        ودي ما ينفعش تتعمل الا في التوكيل أو مركز صيانة معتمد
        موجود عندهم أحد الأجهزة التالية:
        GDS
        or
        Hi-pro
        لأن هي دي الأجهزة الوحيدة اللي تخش بشكل طبيعي على الكنترول بتاع عربيتك وتعدل الكود المخصوص بال Idling والأجهزة دي بتكون أون لاين علشان تجيبلك اخر تحديث..
        [LEFT][FONT=Arial Black][COLOR=#bf0000][SIZE=4][B]Pure Engineering, Pure Satisfaction[/B][/SIZE][/COLOR][/FONT]
        [LEFT]
        [/LEFT]
        [/LEFT]

        Comment


        • #19
          و الله يا مروان العيب ده مش فى فيرنا ولا اتنين ده فى موديل بحاله

          و لو كان ليه حل فى التوكيل كنت عرفت

          بس مش بياخد باله من العيب ده غير اللى بيكون مركز مع عربيته
          [CENTER][SIZE=5][COLOR=gray][COLOR=#000000][SIZE=5][FONT=Times New Roman][B][SIZE=6][COLOR=blue]سبحان الله و بحمده سبحان الله العظيم[/COLOR][/SIZE][/B][/FONT][/SIZE][/COLOR][/COLOR][/SIZE][SIZE=5][COLOR=gray][COLOR=#000000][SIZE=5][/CENTER]
          [CENTER][CENTER][FONT=Times New Roman][B][SIZE=6][COLOR=blue][/COLOR][/SIZE][/B][/FONT][/CENTER]
          [/SIZE][/COLOR][/COLOR][/SIZE][/CENTER]

          Comment


          • #20
            شكراً أ/ مروان و أ/ أحمد كار على الاهتمام و الرد ..
            كده أنا فهمت و لما هاروح التوكيل هاتكلم على نور
            وطبيعى ان الواحد يكون مركز مع العربيه - أنا كده مع القديم عربيتى و عربية حد تانى , فما بالك بعربية زيرو الواحد دافع و لسه بيدفع فيها دم قلبه ...

            عموماً أنا حجزت فى التوكيل يوم السبت اللى جاى و لما هاروح هابقى أقولكو على يوم الاحد على اللى حصل و ربنا يسهل و يهديهم علينا ..

            شكراً ..
            [SIGPIC][/SIGPIC]
            https://www.facebook.com/groups/SWIFTCLUBINEGYPT/

            Comment


            • #21
              المشاركة الأصلية كتبت بواسطة AHMEDCAR مشاهدة المشاركة
              و الله يا مروان العيب ده مش فى فيرنا ولا اتنين ده فى موديل بحاله

              و لو كان ليه حل فى التوكيل كنت عرفت

              بس مش بياخد باله من العيب ده غير اللى بيكون مركز مع عربيته
              ما المصيبة ان التوكيل نفسه ما عندهمش خبر وأنا هابعتلك أمثلة على تعديل و تحديث في أكواد الكنترول الخاصة بالفيرنا من الشركة الأم بس اكتبلي الميل بتاعك
              هانسخكلم حاجة خاصة بخنقة الفيرنات على سبيل المثال الغير مبررة و التوكيل ماعندوش بيها أي خبر ويفضل يدفعك في قطع غيار والمشكلة مابتتحلش
              DE......ION:
              1. Some 2000-2002 Accents with 1.5L SOHC and 1.6L DOHC engines may experience the following symptoms in the summer (hot and humid weather):
                • Slower than usual acceleration after an initial cold start (engine is cold soaked).

                • Greater than usual rpm drop when engaging drive or reverse (on ATM equipped vehicles) after an initial cold start.

              2. Some 2002 1.6L Accents may turn on the "Check Engine" light and store the diagnostic trouble code P0116 (Engine Coolant Temperature Sensor Range/Performance Problem) in the ECM. This code can be falsely set under certain driving conditions.
                Check the Engine Coolant Temperature (ECT) sensor to make sure that it's functioning properly. When the engine is cold soaked, the ECT and Intake Air Temperature should read approximately the same temperature. When the engine is fully warmed-up, the ECT should read about 190° F to 200° F (depending on the cooling fan cycle).
                If the code has been set falsely, perform the ECM software reprogramming procedure using the Hi-Scan Pro as outlined below.


              The ECM program has been revised to improve BOTH
              of the above described conditions.
              The following procedure describes updating the ECM software, using the Hi-Scan Pro.
              NOTE
              This new reprogramming software (#31) supersedes the previous reprograms for "Cold Stumble" (#7 = TSB 01-36-013 and #13 =TSB 02-36-018).
              VEHICLES AFFECTED:
              Cold Stumble:
              All 2000-2002 ACCENT vehicles with 1.5L SOHC and 1.6L DOHC engines.
              P0116:
              2002 Accent with 1.6L DOHC engine. MODEL
              EMISSION
              AFFECTED ECM P/N
              ECM ID
              PASSWORD FOR MANUAL UPDATE
              PREVIOUS
              NEW
              2000 MY ACCENT 1.5L SOHC
              FED
              39110-22550
              39110-22551
              LCF0N50
              LCF0N51
              LCF0N52
              LCF0N53
              LCF0N54
              LCF0N55
              LCF0N56
              LCF0N57
              LCF0N58
              LCF0N59
              2551
              2000 MY ACCENT 1.5L SOHC
              CAL
              39110-22560
              39110-22561
              LCC0N50
              LCC0N51
              LCC0N52
              LCC0N53
              LCC0N54
              LCC0N55
              LCC0N56
              LCC0N57
              LCC0N58
              LCC0N59
              2561
              2001 MY ACCENT 1.5L SOHC
              ALL
              39110-22562
              LCC1N50
              LCC1N51
              LCC1N52
              LCC1N53
              LCC1N54
              LCC1N55
              LCC1N56
              2562
              2001 MY ACCENT 1.6L DOHC
              ALL
              39110-26710
              ADN1N60
              ADN1N61
              ADN1N62
              ADN1N63
              ADN1N64
              ADN1N65
              6710
              2002 MY ACCENT 1.5L SOHC
              ALL
              39110-22563
              LCN2N50
              LCN2N51
              LCN2N52
              LCN2N53
              LCN2N54
              LCN2N55
              LCN2N57
              2563
              2001 MY ACCENT 1.6L DOHC
              ALL
              39110-26711
              ADN2N60
              ADN2N61
              ADN2N62
              ADN2N63
              ADN2N64
              ADN2N65
              ADN2N66
              ADN2N67
              6711
              CAUTIONS BEFORE REPROGRAMMING:
              1. Conduct reprogramming with the ignition key in the "ON" position.

              2. Be careful not to disconnect any cables connected to the vehicle or Hi-Scan Pro during reprogramming.
                WARNING
                If reprogramming is interrupted, the manual update procedure must be used.

              3. Do not start the engine during reprogramming.

              4. Do not turn the ignition key off during reprogramming.

              5. When the reprogramming is completed, turn off the ignition key for 20 seconds before starting the engine.

              REPROGRAMMING PROCEDURE:
              NOTE
              Verify that the vehicle is affected by identifying the vehicle production date and VIN.
              AUTOMATIC UPDATE PROCEDURE:
              1. Attach the DLC (Data Link Connector) cable to the Hi-Scan Pro main body and tighten the 2 bolts securely.

              2. Remove the current system software card from the Hi-Scan Pro and insert the reprogramming software card (with the new ECM program) into the Hi-Scan Pro top slot.

              3. Plug the DLC cable from the Hi-Scan Pro into the data link connector (16-pin connector) to the left of the steering wheel under the instrument panel.

              4. Turn the ignition to the ON
                position.

              5. Turn the Hi-Scan Pro ON
                and pressENTER
                .

              6. Select option "31. LC 00~02MYCOLD STUMBLEAnd02MY P0116"
                and press ENTER
                .

              7. Select option "01. LC 00~02 MY COLD STUMBLE [AUTO]"
                and press ENTER
                . This option automatically detects the ECM type and downloads the correct program.

              8. Enter "1229"
                as the password for the automatic update mode and pressENTER
                .

              9. The Hi-Scan Pro will establish communication and check the ECM ID. The Hi-Scan Pro will reprogram the ECM automatically.

                NOTE
                • The Hi-Scan Pro detects the current ECM ID, assigns the new ECM ID and displays them for a short time.
                • To be prepared in case a reprogramming error occurs, write down the "NEW ECM ID" displayed on the Hi-Scan Pro screen during reprogramming.
                • It will be used during the Manual Update Procedure if the program does not download correctly.
                • If the Hi-Scan Pro does not download the program, use the Manual Update Procedure following this section.
                • Check the ECM IDs displayed on the Hi-Scan Pro screen to verify that the correct ECM software is being downloaded. Refer to the "ECM SPECIFICATION TABLE" on page 2 of this bulletin for the ECM ID listing.


                WARNING
                Do not interrupt the reprogramming at any time. The ECM will be rendered inoperative if the program does not download completely.

              10. When the COMPLETED message is displayed, turn the Hi-Scan Pro OFF
                and the process is complete.

                NOTE
                When reprogramming has been completed successfully, turn the ignition to the OFF position for 20 seconds and then start the engine to check for proper operation.

              MANUAL UPDATE PROCEDURE:
              NOTE
              In the event menu option "01. LC 00-02MY COLD STUMBLE [AUTO]" fails to download the new ECM program, option "02. LC 00-02MY COLD STUMBLE [ERROR]" must be used.
              1. Turn the ignition to the ON
                position.

              2. Turn the Hi-Scan Pro ON
                and press ENTER
                .

              3. Select menu option "31. LC 00~02MY COLD STUMBLEAnd02MY P0116"
                and press ENTER
                .

              4. Select menu option "02. LC 00~02MY COLD STUMBLE [ERROR]"
                for manual update and press ENTER
                .

              5. Choose the correct specification for your vehicle by identifying the VIN and engine and by referring to the "ECM SPECIFICATION TABLE" on page 2 of this bulletin to choose one of 6 choices. Then press ENTER
                .

                NOTE
                If the vehicle is equipped with ECM 39110-22550, use option 01. for 39110-22551.
                NOTE
                If the vehicle is equipped with ECM 39110-22560, use option 02. for 39110-22561.

              6. Select the correct password for Manual Update from the "ECM SPECIFICATION TABLE" on page 2 of this bulletin.
                • Enter the correct password and press ENTER
                  .
                  WARNING
                  If an incorrect password is used, the correct ECM software will not be downloaded.

              7. Wait until the reprogramming is completed. The Hi-Scan Pro will reprogram the ECM.
                NOTE
                Once the password is entered and accepted, therest of the procedure isexactly the same as theautomatic update procedure.

              8. Compare the new ECM ID displayed on the Hi-Scan Pro screen with the one that's listed as the correct new ECM ID in the table on page 2 of this TSB, to make sure that the correct software has been installed.

              9. When the COMPLETED message is displayed, turn the Hi-Scan Pro OFF
                and the process is complete.
                NOTE
                When reprogramming has been completed successfully, turn the ignition to the OFF position for 20 seconds and then start the engine to check for proper operation.

              EXPLANATION OF ERROR MESSAGE:
              1. "INVALID PASSWORD"
                : Please enter the correct password again.

              2. "REPROGRAMMING ERROR PLEASE WAIT FOR RETRY"
                : An error occurred during reprogramming, the Hi-Scan Pro will retry the reprogramming automatically.

              3. "ALREADY REPROGRAMMED"
                or "INCORRECT TARGET ID"
                : The reprogramming has previously been done on this vehicle or the ECM is not the typesubject for this reprogramming procedure.

              4. "REPROGRAM ERROR PLEASE CHECK THE SYSTEM"
                : In this case you must reprogram manually after selecting the menu option "02. LC 00~02MY COLD STUMBLE [ERROR]"
                .

              WARRANTY INFORMATION: OP CODE
              OPERATION
              OP TIME
              CAUSAL PART NUMBER
              OP QTY
              NATURE CODE
              CAUSE CODE
              39175R0F
              ECM Reprogramming
              0.3M/H
              Please refer to the appropriate Part Numbers from page 2 ofthis TSB
              1
              *N03
              ....C40

              *N03: Surge, stumble, hesitate

              ....
              C40: Improper adjustment
              [LEFT][FONT=Arial Black][COLOR=#bf0000][SIZE=4][B]Pure Engineering, Pure Satisfaction[/B][/SIZE][/COLOR][/FONT]
              [LEFT]
              [/LEFT]
              [/LEFT]

              Comment


              • #22
                المشاركة الأصلية كتبت بواسطة AHMEDCAR مشاهدة المشاركة
                و الله يا مروان العيب ده مش فى فيرنا ولا اتنين ده فى موديل بحاله

                و لو كان ليه حل فى التوكيل كنت عرفت

                بس مش بياخد باله من العيب ده غير اللى بيكون مركز مع عربيته
                ما المصيبة ان التوكيل نفسه ما عندهمش خبر وأنا هابعتلك أمثلة على تعديل و تحديث في أكواد الكنترول الخاصة بالفيرنا من الشركة الأم بس اكتبلي الميل بتاعك
                هانسخكلم حاجة خاصة بخنقة الفيرنات على سبيل المثال الغير مبررة و التوكيل ماعندوش بيها أي خبر ويفضل يدفعك في قطع غيار والمشكلة مابتتحلش
                DE......ION:
                1. Some 2000-2002 Accents with 1.5L SOHC and 1.6L DOHC engines may experience the following symptoms in the summer (hot and humid weather):
                  • Slower than usual acceleration after an initial cold start (engine is cold soaked).

                  • Greater than usual rpm drop when engaging drive or reverse (on ATM equipped vehicles) after an initial cold start.

                2. Some 2002 1.6L Accents may turn on the "Check Engine" light and store the diagnostic trouble code P0116 (Engine Coolant Temperature Sensor Range/Performance Problem) in the ECM. This code can be falsely set under certain driving conditions.
                  Check the Engine Coolant Temperature (ECT) sensor to make sure that it's functioning properly. When the engine is cold soaked, the ECT and Intake Air Temperature should read approximately the same temperature. When the engine is fully warmed-up, the ECT should read about 190° F to 200° F (depending on the cooling fan cycle).
                  If the code has been set falsely, perform the ECM software reprogramming procedure using the Hi-Scan Pro as outlined below.


                The ECM program has been revised to improve BOTH
                of the above described conditions.
                The following procedure describes updating the ECM software, using the Hi-Scan Pro.
                NOTE
                This new reprogramming software (#31) supersedes the previous reprograms for "Cold Stumble" (#7 = TSB 01-36-013 and #13 =TSB 02-36-018).
                VEHICLES AFFECTED:
                Cold Stumble:
                All 2000-2002 ACCENT vehicles with 1.5L SOHC and 1.6L DOHC engines.
                P0116:
                2002 Accent with 1.6L DOHC engine. MODEL
                EMISSION
                AFFECTED ECM P/N
                ECM ID
                PASSWORD FOR MANUAL UPDATE
                PREVIOUS
                NEW
                2000 MY ACCENT 1.5L SOHC
                FED
                39110-22550
                39110-22551
                LCF0N50
                LCF0N51
                LCF0N52
                LCF0N53
                LCF0N54
                LCF0N55
                LCF0N56
                LCF0N57
                LCF0N58
                LCF0N59
                2551
                2000 MY ACCENT 1.5L SOHC
                CAL
                39110-22560
                39110-22561
                LCC0N50
                LCC0N51
                LCC0N52
                LCC0N53
                LCC0N54
                LCC0N55
                LCC0N56
                LCC0N57
                LCC0N58
                LCC0N59
                2561
                2001 MY ACCENT 1.5L SOHC
                ALL
                39110-22562
                LCC1N50
                LCC1N51
                LCC1N52
                LCC1N53
                LCC1N54
                LCC1N55
                LCC1N56
                2562
                2001 MY ACCENT 1.6L DOHC
                ALL
                39110-26710
                ADN1N60
                ADN1N61
                ADN1N62
                ADN1N63
                ADN1N64
                ADN1N65
                6710
                2002 MY ACCENT 1.5L SOHC
                ALL
                39110-22563
                LCN2N50
                LCN2N51
                LCN2N52
                LCN2N53
                LCN2N54
                LCN2N55
                LCN2N57
                2563
                2001 MY ACCENT 1.6L DOHC
                ALL
                39110-26711
                ADN2N60
                ADN2N61
                ADN2N62
                ADN2N63
                ADN2N64
                ADN2N65
                ADN2N66
                ADN2N67
                6711
                CAUTIONS BEFORE REPROGRAMMING:
                1. Conduct reprogramming with the ignition key in the "ON" position.

                2. Be careful not to disconnect any cables connected to the vehicle or Hi-Scan Pro during reprogramming.
                  WARNING
                  If reprogramming is interrupted, the manual update procedure must be used.

                3. Do not start the engine during reprogramming.

                4. Do not turn the ignition key off during reprogramming.

                5. When the reprogramming is completed, turn off the ignition key for 20 seconds before starting the engine.

                REPROGRAMMING PROCEDURE:
                NOTE
                Verify that the vehicle is affected by identifying the vehicle production date and VIN.
                AUTOMATIC UPDATE PROCEDURE:
                1. Attach the DLC (Data Link Connector) cable to the Hi-Scan Pro main body and tighten the 2 bolts securely.

                2. Remove the current system software card from the Hi-Scan Pro and insert the reprogramming software card (with the new ECM program) into the Hi-Scan Pro top slot.

                3. Plug the DLC cable from the Hi-Scan Pro into the data link connector (16-pin connector) to the left of the steering wheel under the instrument panel.

                4. Turn the ignition to the ON
                  position.

                5. Turn the Hi-Scan Pro ON
                  and pressENTER
                  .

                6. Select option "31. LC 00~02MYCOLD STUMBLEAnd02MY P0116"
                  and press ENTER
                  .

                7. Select option "01. LC 00~02 MY COLD STUMBLE [AUTO]"
                  and press ENTER
                  . This option automatically detects the ECM type and downloads the correct program.

                8. Enter "1229"
                  as the password for the automatic update mode and pressENTER
                  .

                9. The Hi-Scan Pro will establish communication and check the ECM ID. The Hi-Scan Pro will reprogram the ECM automatically.

                  NOTE
                  • The Hi-Scan Pro detects the current ECM ID, assigns the new ECM ID and displays them for a short time.
                  • To be prepared in case a reprogramming error occurs, write down the "NEW ECM ID" displayed on the Hi-Scan Pro screen during reprogramming.
                  • It will be used during the Manual Update Procedure if the program does not download correctly.
                  • If the Hi-Scan Pro does not download the program, use the Manual Update Procedure following this section.
                  • Check the ECM IDs displayed on the Hi-Scan Pro screen to verify that the correct ECM software is being downloaded. Refer to the "ECM SPECIFICATION TABLE" on page 2 of this bulletin for the ECM ID listing.


                  WARNING
                  Do not interrupt the reprogramming at any time. The ECM will be rendered inoperative if the program does not download completely.

                10. When the COMPLETED message is displayed, turn the Hi-Scan Pro OFF
                  and the process is complete.

                  NOTE
                  When reprogramming has been completed successfully, turn the ignition to the OFF position for 20 seconds and then start the engine to check for proper operation.

                MANUAL UPDATE PROCEDURE:
                NOTE
                In the event menu option "01. LC 00-02MY COLD STUMBLE [AUTO]" fails to download the new ECM program, option "02. LC 00-02MY COLD STUMBLE [ERROR]" must be used.
                1. Turn the ignition to the ON
                  position.

                2. Turn the Hi-Scan Pro ON
                  and press ENTER
                  .

                3. Select menu option "31. LC 00~02MY COLD STUMBLEAnd02MY P0116"
                  and press ENTER
                  .

                4. Select menu option "02. LC 00~02MY COLD STUMBLE [ERROR]"
                  for manual update and press ENTER
                  .

                5. Choose the correct specification for your vehicle by identifying the VIN and engine and by referring to the "ECM SPECIFICATION TABLE" on page 2 of this bulletin to choose one of 6 choices. Then press ENTER
                  .

                  NOTE
                  If the vehicle is equipped with ECM 39110-22550, use option 01. for 39110-22551.
                  NOTE
                  If the vehicle is equipped with ECM 39110-22560, use option 02. for 39110-22561.

                6. Select the correct password for Manual Update from the "ECM SPECIFICATION TABLE" on page 2 of this bulletin.
                  • Enter the correct password and press ENTER
                    .
                    WARNING
                    If an incorrect password is used, the correct ECM software will not be downloaded.

                7. Wait until the reprogramming is completed. The Hi-Scan Pro will reprogram the ECM.
                  NOTE
                  Once the password is entered and accepted, therest of the procedure isexactly the same as theautomatic update procedure.

                8. Compare the new ECM ID displayed on the Hi-Scan Pro screen with the one that's listed as the correct new ECM ID in the table on page 2 of this TSB, to make sure that the correct software has been installed.

                9. When the COMPLETED message is displayed, turn the Hi-Scan Pro OFF
                  and the process is complete.
                  NOTE
                  When reprogramming has been completed successfully, turn the ignition to the OFF position for 20 seconds and then start the engine to check for proper operation.

                EXPLANATION OF ERROR MESSAGE:
                1. "INVALID PASSWORD"
                  : Please enter the correct password again.

                2. "REPROGRAMMING ERROR PLEASE WAIT FOR RETRY"
                  : An error occurred during reprogramming, the Hi-Scan Pro will retry the reprogramming automatically.

                3. "ALREADY REPROGRAMMED"
                  or "INCORRECT TARGET ID"
                  : The reprogramming has previously been done on this vehicle or the ECM is not the typesubject for this reprogramming procedure.

                4. "REPROGRAM ERROR PLEASE CHECK THE SYSTEM"
                  : In this case you must reprogram manually after selecting the menu option "02. LC 00~02MY COLD STUMBLE [ERROR]"
                  .

                WARRANTY INFORMATION: OP CODE
                OPERATION
                OP TIME
                CAUSAL PART NUMBER
                OP QTY
                NATURE CODE
                CAUSE CODE
                39175R0F
                ECM Reprogramming
                0.3M/H
                Please refer to the appropriate Part Numbers from page 2 ofthis TSB
                1
                *N03
                ....C40

                *N03: Surge, stumble, hesitate

                ....C40: Improper adjustment
                [LEFT][FONT=Arial Black][COLOR=#bf0000][SIZE=4][B]Pure Engineering, Pure Satisfaction[/B][/SIZE][/COLOR][/FONT]
                [LEFT]
                [/LEFT]
                [/LEFT]

                Comment


                • #23
                  اسف على التكرار غير المقصود للمشاركة
                  الرجاء من مشرف هيونداي حذف المكرر
                  [LEFT][FONT=Arial Black][COLOR=#bf0000][SIZE=4][B]Pure Engineering, Pure Satisfaction[/B][/SIZE][/COLOR][/FONT]
                  [LEFT]
                  [/LEFT]
                  [/LEFT]

                  Comment


                  • #24
                    المشاركة الأصلية كتبت بواسطة AHMEDCAR مشاهدة المشاركة
                    حساس ال tbs

                    بيكون ماسك البوابه بتاعه النافولد لانه بيقيس درجه فتح البوابه من خلال ضغط السائق على دواسه البنزين و منها بيدى اوردر للكنترول بكميه النزين المطلوب دخوله لعمليه الاحتراق

                    و هو اصل على السلانسيه بيكون فاتح البوابه سنه بسيطه من اجل دخول الهواء اللى الموتور

                    و بالتالى اول ما بنبطل العربيه الحساس بيتفصل عنه الكهرباء بالتالى بيسيب البوابه

                    فبتسمع الصوت ده ما تقلقش ده طبيعى جدا جدا
                    حساس الTPS مبيمسكش البوابة ولا بياثر عليها باى شكل من الاشكال

                    حساسTPS بيقراء درجة فتح البوابة فقط و التحكم فى الفتح و القفل بيبقى عن طريق ضغط السائق على دواسة البنزين و توصيل الحركة دى الى البوابة من خلال سلك البنزين او من خلال موتور كهربائى لو العربية فيها بوابة كهربائية التشغيل بالتالى الTPS بيقول للكونترول البوابة بتعمل ايه لكن هو شخصيا مش بيتحكم فى حركتها

                    MMamdouh
                    [CENTER]What is the difference between ignorance and apathy?...I don't know & I don't care[/CENTER]

                    [CENTER][SIGPIC][/SIGPIC][/CENTER]


                    [SIZE=6][marq="3;right;3;scroll"]اللى ميعرفش... يقول هجس[/marq][/SIZE]

                    [marq="Error"]what goes around... comes around[/marq]


                    [CENTER][URL="http://www.cardomain.com/ride/567267"]MMamdouh's Lanos on CarDomain
                    [/URL][/CENTER]

                    [URL="http://www.nilemotors.net/Nile/showthread.php?t=85421"]
                    [/URL]

                    Comment


                    • #25
                      المشاركة الأصلية كتبت بواسطة MMamdouh مشاهدة المشاركة
                      حساس الTPS مبيمسكش البوابة ولا بياثر عليها باى شكل من الاشكال

                      حساسTPS بيقراء درجة فتح البوابة فقط و التحكم فى الفتح و القفل بيبقى عن طريق ضغط السائق على دواسة البنزين و توصيل الحركة دى الى البوابة من خلال سلك البنزين او من خلال موتور كهربائى لو العربية فيها بوابة كهربائية التشغيل بالتالى الTPS بيقول للكونترول البوابة بتعمل ايه لكن هو شخصيا مش بيتحكم فى حركتها

                      MMamdouh
                      1111111++++++++
                      لأن وظيفته من اسمه
                      Throttle Position Sensor
                      لأنه بيقوم بقراءة نسبة فتح وقفل الButter Flay Valve أو الThrottle Plate
                      [LEFT][FONT=Arial Black][COLOR=#bf0000][SIZE=4][B]Pure Engineering, Pure Satisfaction[/B][/SIZE][/COLOR][/FONT]
                      [LEFT]
                      [/LEFT]
                      [/LEFT]

                      Comment


                      • #26
                        تمام يا ممدوح

                        بس انا عندى فى الهيونداى البوابه طالع منها دراع و داخل فى الحساس و من خلال حركه البوابه الحساس بيقيس

                        العربيه محتاجه وقود قد ايه

                        و انا لما قولت انه بيتحكم فيها كان قصدى ان البوابه بتكون محمله عليه فقط فى السلانسيه لكن بعد كده كل الشغل على البوابه
                        [CENTER][SIZE=5][COLOR=gray][COLOR=#000000][SIZE=5][FONT=Times New Roman][B][SIZE=6][COLOR=blue]سبحان الله و بحمده سبحان الله العظيم[/COLOR][/SIZE][/B][/FONT][/SIZE][/COLOR][/COLOR][/SIZE][SIZE=5][COLOR=gray][COLOR=#000000][SIZE=5][/CENTER]
                        [CENTER][CENTER][FONT=Times New Roman][B][SIZE=6][COLOR=blue][/COLOR][/SIZE][/B][/FONT][/CENTER]
                        [/SIZE][/COLOR][/COLOR][/SIZE][/CENTER]

                        Comment

                        Working...
                        X